Results 1 to 8 of 8

Thread: Crashed Test Prop?

  1. #1
    Member
    Online : d_nelly78 is offline
    Join Date : Mar 2012
    Posts : 991
    Post Thanks / Like
    Array

    Default Crashed Test Prop?

    I have a few bottles of crashed test p from a private lab I use. Only 4 of the 10 prop crashed. I've researched how to bring it back but am trying not to pop off caps and have to vent with a pin while warming in very hot water. Tried warming with just hot water from the tap but its not working for me. Any words of wisdom y'all?

  2. #2
    Ozzy "Osbourne" VIP
    ozzy69's Avatar
    Online : ozzy69 is offline
    Join Date : Apr 2011
    Posts : 770
    Post Thanks / Like
    Array

    Default

    Add just a touch more BA after you heat it up

  3. #3
    ---
    Online : Udeluz is offline
    Join Date : May 2011
    Posts : 2,438
    Post Thanks / Like
    Array

    Default

    Put them in a pan with about 1/2 of water and bring them up to 245-255 degrees for a few minutes.

  4. #4
    Super Moderator
    NavyChief's Avatar
    Online : NavyChief is offline
    Join Date : Mar 2014
    Posts : 503
    Post Thanks / Like
    Array

    Default

    Don't sweat it brother until u are ready to use the vial. Then just take a small tupperware container. Fill it about an 1 1/2 to 2 in. Deep with water. Microwave the water for 2 or 3 mins until boiling hard. Pull it out and sit it on the counter. Set the crashed vial in the water. It should be fine in a cpl mins. If not, just heat the water on the stove on low, sit the vials in the water then until it clears. No worries.
    SuperMod@AB
    Navy Chief, every where I go

  5. #5
    Member
    Online : d_nelly78 is offline
    Join Date : Mar 2012
    Posts : 991
    Post Thanks / Like
    Array

    Default

    So the only way to save it is to pop of the top, heat, and vent with a pin. Possibly add some ba. Which makes these definitely just for personal use.

  6. #6
    Ozzy "Osbourne" VIP
    ozzy69's Avatar
    Online : ozzy69 is offline
    Join Date : Apr 2011
    Posts : 770
    Post Thanks / Like
    Array

    Default

    Yes

  7. #7
    ---
    Online : Udeluz is offline
    Join Date : May 2011
    Posts : 2,438
    Post Thanks / Like
    Array

    Default

    Quote Originally Posted by d_nelly78 View Post
    So the only way to save it is to pop of the top, heat, and vent with a pin. Possibly add some ba. Which makes these definitely just for personal use.

    Try without popping the top first. I have been successful many times doing it this way. It has a melting point of 245-255 so make sure you get up to that temp.

  8. #8
    Member
    Online : d_nelly78 is offline
    Join Date : Mar 2012
    Posts : 991
    Post Thanks / Like
    Array

    Default

    Was able to bring back the prop pretty easily with heat but a few days ago I received some crashed tne. Did everything I could with heat and venting with a pin and it still crashed within 24hrs. Just added about 2ml of another labs tne to a couple vials to see if that helps. If not I will still use but I will have to warm it up a lil more than usual when I pin it pwo. Its kind of a pain in the ass but after heating it up last night and shaking vigorously I was still able to pin with a 25 ga 5/8 no dead space pin in my bi with no probs.

Similar Threads

  1. npp+prop+var or test e+eq+var
    By isoletol in forum Anabolic Steroids & Other Hormones
    Replies: 20
    Last Post: 08-24-2011, 04:05 PM
  2. Opiox Test Prop
    By Mr.Cip in forum EuroKing
    Replies: 1
    Last Post: 07-27-2011, 01:06 AM
  3. prop
    By hoyt323 in forum Anabolic Steroids & Other Hormones
    Replies: 21
    Last Post: 12-05-2010, 10:43 PM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •